Fast Tracks

Model Railroading Discussion Forums

Return To The Fast Tracks Website

The Fast Tracks discussion forums have been closed. Click Here for more information.

It is currently Sat Oct 05, 2024 5:11 am

All times are UTC - 5 hours [ DST ]




Forum locked This topic is locked, you cannot edit posts or make further replies.  [ 5 posts ] 
Author Message
 Post subject: Sn3 curved turnout
PostPosted: Tue Nov 25, 2008 4:57 pm 
Offline

Joined: Sun Feb 26, 2006 4:56 pm
Posts: 17
Location: Eden Prairie, MN
I have a spot on my layout that needs curved turnout. Originally I was going to use a #8 twist ties for this turnout, but the #8 point form tool that I was going to use is no longer available to me. Since I don't want to purchase a point form tool for #8s for just one turnout, I am thinking about using a #6 instead. I plan to have the inside radius at 30" and the outside will float to what ever it takes. Do you see any issues with doing this? Any comments or suggestions.

Thanks

Jim McHenry


Top
 Profile  
 
 Post subject: Re: Sn3 curved turnout
PostPosted: Tue Nov 25, 2008 6:33 pm 
Offline
Site Admin

Joined: Fri May 07, 2004 11:22 pm
Posts: 311
Location: Port Dover, Ontario
Hi Jim,

As long as you minimum radius is 30" you should not have any issues as the outer radius will be much larger. If you can keep above 30" inside that would be even better, as the inside radius of a curved turnout is a compound radius and there will be a very short section that ends up less than 30"

Tim

_________________
Cheers!

Tim Warris
Fast Tracks
http://www.fast-tracks.net
service@fast-tracks.net


Top
 Profile  
 
 Post subject: Re: Sn3 curved turnout
PostPosted: Wed Nov 26, 2008 11:49 am 
Offline

Joined: Sun Feb 26, 2006 4:56 pm
Posts: 17
Location: Eden Prairie, MN
Tim

The radius of the inside track will actually be 30.75" and I'm not sure if I can alter that much at this point. Almost all of my locomotives are P-B-L and are designed for a minimum radius of 26", but that is really pushing it. The largest loco that I will own is a K-27 but at sometime I will probably have visiting power that will go up to a K-37. Will the "pinch point on the curve go down below the 26"r? If so I should probably rethink and or re engineer that spot on the layout.

Thanks

Jim


Top
 Profile  
 
 Post subject: Re: Sn3 curved turnout
PostPosted: Wed Nov 26, 2008 11:54 am 
Offline
Site Admin

Joined: Fri May 07, 2004 11:22 pm
Posts: 311
Location: Port Dover, Ontario
You should be fine with these specs.

_________________
Cheers!

Tim Warris
Fast Tracks
http://www.fast-tracks.net
service@fast-tracks.net


Top
 Profile  
 
 Post subject: Re: Sn3 curved turnout
PostPosted: Mon Dec 01, 2008 11:19 am 
Offline

Joined: Sun Feb 26, 2006 4:56 pm
Posts: 17
Location: Eden Prairie, MN
It looks like I'll be able to use the #8 after all. I tought my friend had given his #8 tools to another friend in Chicago. It turns out he did keep the tools and is going to allow me to borrow the point form tool next weekend. I love it when a plan comes together!

Jim


Top
 Profile  
 
Display posts from previous:  Sort by  
Forum locked This topic is locked, you cannot edit posts or make further replies.  [ 5 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group