Fast Tracks

Model Railroading Discussion Forums

Return To The Fast Tracks Website

The Fast Tracks discussion forums have been closed. Click Here for more information.

It is currently Thu Mar 28, 2024 7:20 am

All times are UTC - 5 hours [ DST ]




Forum locked This topic is locked, you cannot edit posts or make further replies.  [ 4 posts ] 
Author Message
PostPosted: Fri Jan 25, 2008 4:57 pm 
Offline

Joined: Fri Jan 25, 2008 4:17 pm
Posts: 2
Hi all!

I've bought a few #5 TwistTies that I plan on building with an outer radius of 100cm (40"). What I'm trying to figure out is how one calculates the inner radius.

Any input appreciated!

/Ulf


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jan 25, 2008 7:25 pm 
Offline
User avatar

Joined: Sat Aug 13, 2005 10:48 am
Posts: 365
Location: East Texas - USA
Ulf,

Calculating the diverging route curve would be very dependent on the uniformity of the curve(s), and also the use of a straight vs. a curved frog. You can however, layout the 'straight' section along your 100cm outer curve - and then marking the centerline of the resulting diverging curve.

Take a ruler and draw a straight distance of 1cm just touching the curve centerline points. At the midway point (50mm) carefully measure to the curve offset (location of the curve at that mid-point).

This is the mid-cord ordinate. The offset can then be plugged into the formula for determining the resulting curve radius:

L= Length between curve points (base)
z = Max Offset ( ~1/2 base to intersect)
r (effective radius of the curve) = (L^2) / (8z) + z/2

Thus if the offset is say 2.6mm (EXAMPLE VALUE ONLY):
r = (100^2) / ( 8 * 2.6 ) + (2.6 / 2)
r = (10,000) / ( 20.8 ) + (1.3)
r= ~ 482.07mm (or close to 19" radius)

If the offset is only 1.5mm at the mid point along a 100mm cord you'll end up with about a 33" (836.33mm) radius.

Note: That's NOT the answer - just an example - the actually measured offset would need to be put into the formula. You can see that the measured mid-cord ordinate offset will be very small and getting good accuracy in measuring is important for reliable results. :shock:

_________________
-ed mccamey-
COSLAR RR - http://www.coslar.us/
NMRA Standards and Conformance Department
PROTO & FINE Scale Coordinator
I estimate I have about 5 pounds of coupler springs somewhere in the vicinity of my workbench.


Last edited by emccamey on Fri Jan 25, 2008 7:38 pm, edited 1 time in total.

Top
 Profile  
 
 Post subject: Curved radius
PostPosted: Fri Jan 25, 2008 7:36 pm 
Offline

Joined: Tue Mar 14, 2006 9:26 pm
Posts: 25
I get a little over 18" in 3rdplanit. You can take a straight turnout and flex it to any desired radius.


Top
 Profile  
 
 Post subject:
PostPosted: Sat Jan 26, 2008 3:40 am 
Offline

Joined: Fri Jan 25, 2008 4:17 pm
Posts: 2
thanks guys!


Top
 Profile  
 
Display posts from previous:  Sort by  
Forum locked This topic is locked, you cannot edit posts or make further replies.  [ 4 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 16 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group